/
Longitudinal Rebar Property for Spiral Rebar

Longitudinal Rebar Property for Spiral Rebar

Summary


  • View or edit property information for classification, geometry, analysis, quantity settings of the Longitudinal Rebar Group that is dependent on the Spiral Rebar.

 

How to Run


  • Select the Spiral Longitudinal Rebar Group on the screen.

 

Explanation


Common Tab

 

  • [Classification]
    Set the classification properties of the rebar group.

    • Name : Enter the name of the rebar group.

    • Rebar Type : Displays the rebar type.

    • Grade : Sets the material grade of the rebar group.

  • [Specification]
    Sets the specification of the rebar group.

    • Code : Sets the rebar specification.

    • Diameter : Select the rebar diameter. This is enabled only when a code is selected.

    • Nominal Diameter : Enter the nominal diameter of the rebar.

    • Bending Radius : Enter the bending radius of the rebar.

    • Maximum Length : Displays the length of the longest rebar within the rebar group.

    • Minimum Length : Displays the length of the shortest rebar within the rebar group.

  • Diameter : This is enabled only when a code is selected.

  • Nominal Diameter : Once the ‘Diameter’ is set, the nominal diameter is displayed. This can be entered manually only when ‘Code : None’.

  • Bending Radius : Once the ‘Diameter’ is set, the bending radius is displayed. This can also be input manually.

  • [Hook]
    Set the shape of a hook.

    • Differenct Start/End Hook : Set whether to apply hook settings differently to the start and end point of the hook.

    • Hook Type : Select the type of hook.

    • Angle : Enter the angle of the hook.

    • Radius : Enter the radius of the hook.

    • Length : Enter the length of the hook.

  • Differenct Start/End Hook

    • Off : Applies same hook settings to start and end point of the hook.

    • On : Applies different hook settings to start and end point of the hook. This enables the Start/End Point Tab button.

  • Hook Type : Select the hook type based on the angle.

    • No Hook : The hook is not created.

    • Custom Hook : The hook is created based on the hook angle entered by the user.

    • ±180°, ±135°, ±90° : The hook is created according to the information specified in ‘Rebar Specification’. For this setting, the angle/radius/length cannot be set manually.

  • [Offset]
    Adjust the extension length at both ends of the rebar.

    • Start/End Length : Enter the extension length at the start and end of the rebar. Enter a positive (+) value to shorten, and a negative (-) value to extend.

 

Array Tab

 

  • [Arrangement]
    Sets the spacing for the rebars.

    • Number of Rebars : Enter the number of longitudinal rebars that are arranged in the spiral rebar. The rebars are spaced equally based on the number of rebars entered.

  • For an independent longitudinal rebar, the Hidden Line option can be used.

  • Hidden Line : Reference line used to draw longitudinal rebars.

    • The initial settings are set to 'Adjustable Spacing : 0.2 m', and these are typically not set separately. However, to reduce the error margin for independent longitudinal rebar shapes such as curved reinforcement, the user can reduce the size of spacing.

    • 간The spacing setting is same as the ‘Arrangement Setting’.

  • [Splice]
    Set the splice for the rebar group.

  • Edit Splice by Table : Selects the splice method. When enabled, the splice settings can be modified from the table.

    • Off : The user edits the splice through the settings.

      • Splice Type : Selects the type of rebar splice. (None / Lap / Coupler / Welding)

        • Lap : This is a multilayer splice method that connects the rebars into a continuous line of rebar.

        • Coupler : This splice method connects two rebars using a coupler.

        • Welding : This splice method connects two rebars using welding.

      • Two-Way Splice : Sets the splice direction.

        • On : Sets the splice direction towards the start and end points. This enables the Forward & Backward Tab, and each splice direction can be set.

        • Off : Sets the splice in one direction.

          • Reverse Direction : When enabled, the splice direction is reversed.

      • Bar Length : Enter the splice spacing. Different spacings can be used. The splice can be created by clicking on the representative rebar.

      • Alternate Length : Enter the spacing for 1Cycle and 2Cycle splices. This arranges the splice in a zig-zag shape.

      • Lap Length : Enter the length of the lap splice. (Only enabled for Lap Type)

      • Bar Arrangement : Set the arrangement type of overlapping splices. (Only enabled for Lap Type)

        • Left-Right : Arranged in a zig-zag form from left to right from the start point.

        • Right-Left : Arranged in a zig-zag form from right to left from the start point.

    • On : Edit the splice settings from the table.

      • Splice Table

        • The diameter for each sub-group (Rebar groups separated by splice) can be modified.

        • Direction : The direction of the splice can be set. (F : Forward, B : Backward)

  • [Variable Rebar Name]
    Sets the name rule within the rebar group.

    • Array Group : Set the name of each arranged rebar differently.

    • Splice Group : Set the name of each regar group according to the splice group.

 

Construction Tab

 

 

Reference Materials


 

Related content

Spiral Rebar Property
Spiral Rebar Property
More like this
Longitudinal Rebar Property
Longitudinal Rebar Property
More like this
Transverse Rebar Property
Transverse Rebar Property
More like this
Shear Reinforcement Property
Shear Reinforcement Property
More like this
Spiral Rebar Property
Spiral Rebar Property
More like this