개요
평면에서 작도한 Rebar를 3D로 배치하여 Rebar Group을 생성합니다.
Summary
Create a Rebar Group by placing the drawn Rebar in 3D.
How to Run
Ribbon Menu > [Model] Tab > [Component] Group > Rebar > Array
Explanation
Tapered Array
방법Tapered Array 방법으로 철근을 배열합니다.
변단면의 종방향 단면 변화에 따른 철근 형상의 변화를 반영합니다Method
Arrange the rebars using the Taped Array method.
This reflects the changes in the rebar shape according to the longitudinal section change of the side section.
[Tab] Property
[Arrangement]
횡철근의 배치 간격을 설정합니다Sets the placement interval for the transverse rebar.
Info |
---|
Transverse Rebar Property > Refer Arrangement 참고 |
[Tab] Array
[Method]
Tapered Array를 선택합니다
철근을 배열하는 방식을 선택합니다. 배열 방식에 따라 Array 설정이 변경됩니다.Choose how the rebars are arranged. Array setting changes based on the arrangement method.
Select Tapered Array.
Expand | ||
---|---|---|
| ||
|
[Select Rebar]
배열할 철근Select the rebars (Draw Plane 상태Status) 을 선택합니다to arrange.[Select Array Target Member]
선택한 철근이 배열될 Target Member를 선택합니다. 단일 부재에 철근을 배열하는 경우, 선택하지 않습니다Select the target member on which the selected rebars will be arranged. Do not check if rebars are arranged on a single member.[Define End Plane]
철근이 배열될 종점 평면을 정의합니다Defines the plane of the end point where the rebars will be arranged.
Info |
---|
[Reference Path of Spacing]
철근의 배열 경로를 정의합니다Defines the arrangement path of the rebar.Geometric Line of 1D Member : 선택한 부재의 중심선을 배열 경로로 지정합니다Specifies the center line of the selected member as the array path.
Select Edge : Line 객체를 선택하여 배열 경로로 지정합니다Line Select a Line object and set it as the Array path.
[Longitudinal Rebar Option]
종철근의 진행방향 기준을 설정합니다Sets the criteria for the longitudinal direction of the longitudinal rebar.
Expand | ||
---|---|---|
| ||
|
Array Along Path
방법Method
Arrange the rebars using the Array Along Path 방법으로 철근을 배열합니다method.
Only changes to the section above the Rebar Draw Plane 위의 단면에 대한 변화만을 고려할 수 있으며, 종방향 단면 변화는 반영하지 않습니다are considered and longitudinal section changes are not reflected.
[Tab] Property
[Arrangement]
횡철근의 배치 간격을 설정합니다Sets the placement interval for the transverse rebar.
Info |
---|
Transverse Rebar Property > Refer Arrangement 참고 |
[Tab] Array
[Method]
Array Along Path를 선택합니다
철근을 배열하는 방식을 선택합니다. 배열 방식에 따라 Array 설정이 변경됩니다.Choose how the rebars are arranged. Array setting changes based on the arrangement method.
Select Array Along Path.
[Select Rebar]
배열할 철근Select the rebars (Draw Plane 상태)을 선택합니다Status) to be arranged.[Select Array Target Member]
선택한 철근이 배열될 Target Member를 선택합니다. 단일 부재에 철근을 배열하는 경우, 선택하지 않습니다Select the target member on which the selected rebars will be arranged. Do not check if rebars are arranged on a single member.[Define End Plane]
철근이 배열될 종점 평면을 정의합니다Defines the plane of the end point where the rebars will be arranged.
Info |
---|
[Reference Path of Spacing]
철근의 배열 경로를 정의합니다Defines the arrangement path of the rebar.Geometric Line of 1D Member : 선택한 부재의 중심선을 배열 경로로 지정합니다Specifies the center line of the selected member as the array path.
Select Edge : Line 객체를 선택하여 배열 경로로 지정합니다Select a Line object and set it as the Array path.
[Longitudinal Rebar Option]
종철근의 진행방향 기준을 설정합니다Sets the criteria for the longitudinal direction of the longitudinal rebar.
Expand | ||
---|---|---|
| ||
|
Sweep Array
방법Method
Arrange the rebars using the Sweep Array 방법으로 철근을 배열합니다.횡철근을 구성하는 Draw Point들의 경로를 임의로 지정하여 철근을 배열합니다method.
Arrange the rebars by randomly specifying the path of the draw points that make up the transverse rebars.
[Tab] Property
[Arrangement]
횡철근의 배치 간격을 설정합니다Sets the placement interval for the transverse rebar.
Info |
---|
Transverse Rebar Property > Refer Arrangement 참고 |
[Tab] Array
[Method]
Sweep Array를 선택합니다
철근을 배열하는 방식을 선택합니다. 배열 방식에 따라 Array 설정이 변경됩니다.Choose how the rebars are arranged. Array settings change depending on how they are arranged.
Select Sweep Array.
[Select Rebar]
배열할 철근Select the rebars (Draw Plane 상태)을 선택합니다Status) to be arranged.[Select Array Target Member]
선택한 철근이 배열될 Target Member를 선택합니다. 단일 부재에 철근을 배열하는 경우, 선택하지 않습니다Select the target member on which the selected rebars will be arranged. Do not check if rebars are arranged on a single member.[Draw Point Path]
횡철근의 Define the path for each Draw Point 각각의 경로를 정의합니다. Draw Point 중 하나라도 경로가 지정되지 않은 경우, 철근이 배열되지 않습니다of the transverse rebar. If any of the Draw Points are not specified, then the rebars will not be arranged.
Info |
---|
[Define End Plane]
철근이 배열될 종점 평면을 정의합니다Defines the plane of the end point where the rebars will be arranged.
Info |
---|
[Reference Path of Spacing]
철근의 배열 경로를 정의합니다Defines the arrangement path of the rebar.Geometric Line of 1D Member : 선택한 부재의 중심선을 배열 경로로 지정합니다Specifies the center line of the selected member as the array path.
Select Edge : Line 객체를 선택하여 배열 경로로 지정합니다Select a Line object and set it as the Array path.
[Longitudinal Rebar Option]
종철근의 진행방향 기준을 설정합니다Sets the criteria for the longitudinal direction of the longitudinal rebar.
Expand | ||
---|---|---|
| ||
|
Cancel Array
방법배열된 철근을 배열 전, 즉 Draw Plane 상태로 복구시킵니다.
Method
Restores the arranged rebars to the Draw Plane state before the arrangement.
[Tab] Array
[Method]
Cancel Array를 선택합니다
철근을 배열하는 방식을 선택합니다. 배열 방식에 따라 Array 설정이 변경됩니다.Choose how the rebars are arranged. Array setting changes based on the arrangement method.
Select Cancel Array.
[Select Rebar]
배열된 철근 그룹을 선택합니다. 복수의 철근 그룹을 선택할 수 있습니다Select an arrayed rebar group. The User can select multiple rebar group.
Info |
---|
단일 철근 그룹의 Cancel Array는 Neutral 상태에서 철근 그룹을 선택하여 Draw Plane 상태로 복구시킬 수 있습니다. |
The Cancel Array of a single rebar group can be restored to the Draw Plane state by selecting the rebar group in the Neutral state. |