Summary | Action rule of Rebar Property Option의 동작 규칙Option | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Related Function | Model > Component > Rebar > Transverse Rebar Longitudinal Rebar Stirrup Rebar Independent Longitudinal Rebar | ||||||||||||
Type |
|
Q.
Hook와 Align Option이 CIM에서 어떻게 적용되는지 궁금합니다.A. Hook는 철근 단부에 갈고리를 생성하는 기능입니다. Align Option은 철근의 정렬 방식을 결정합니다.
이 문서는 Draw Rebar Mode에서 철근 배근 진행 간 Rebar Property내의 Hook와 Align Option이 동작하는 규칙에 대한 기술 문서입니다.
해당 문서에서는 철근들의 모델링 간 적용되는 Hook의 각 기능의 동작 및 활용 방법,
그리고 평면으로부터 정렬을 정의하는 Opiton들의 동작 규칙에 대하여 기술되어 있습니다.
Hook
Hook는 철근 단부에 갈고리 형상을 생성하는 기능입니다.
Hook Property는 두 기능으로 구분할 수 있습니다I wonder how Hook and Align Option are applied in CIM.
A. Hook is a function that creates a hook at the end of rebar. The Align Option determines how the reinforcing bars are aligned.
This document is a technical document about the rules for the Hook and Align Option in the Rebar Property to operate between rebar in Draw Rebar Mode.
In this document, the operation and utilization method of each function of hook applied between modeling of reinforcing bars,
And the rules of operation of Opitons that define alignment from the plane are described.
Hook
Hook is a function that creates a hook shape at the end of a reinforcing bar.
Hook Property can be divided into two functions.
● Direction / Location
● Angle / Radius / Length
Info |
---|
Different Start/End Hook 기능은 양 끝단의 갈고리의 설정을 다르게 하고싶을 때 활성화 하는 기능입니다. 해당 기능을 활성화하게 되면 시작과 끝의 갈고리의 설정을 각각 입력할 수 있도록 function is activated when you want to set different hooks at both ends. If you activate the function, you can enter the setting of the hook at the beginning and the end, respectively. The Start Point / End Point 탭이 활성화 됩니다tab becomes active. |
Direction / Location
▶ Direction
Rebar Property의 Direction은 Hook의 생성 방향을
규정하는 기능입니다.
Direction은 두 가지 옵션으로 구성 되어 있습니다
● Plane : 철근이 작도된 평면 상으로 Hook이 생성됩니다.
● Custom : 평면이 아닌 방향으로 사용자가 지정한
Rotate Angle로 Hook이 생성됩니다.
Custom의 기능을 선택할 경우 Rotate Angle 값을
입력할 수 있는 창이 활성화되며
Hook이 종속되어 있는 철근을 기준으로
입력 값만큼 회전하게 됩니다.
그림 1. Rotate Angle과 Hook Angle의 Hook 생성 방향 비교
▶ Location
Rebar Property의 Location은
Offset이 적용 되는 위치를 결정합니다.
즉 Hook 가 생성되는 위치에 관한 기능입니다.
- Normal : 횡철근 Line의 내측을 기준으로
Hook이 생성됩니다.- Extended : 횡철근 Line 외측을 기준으로
Hook이 생성됩니다.
그림 2. Location 설정에 따른 비교
그림 3. Hook Length와 Part Length
Hook Length와 Part Length의 동작 차이
Hook Length와 Part Length에 같은 입력값을 설정 하더라도 두 Property의 동작 규칙의 차이로 인하여
다른 형상이 나타나게 됩니다.
Hook Length의 경우 Hook Length를 Hook Bending Radius 의 곡선부 이후에 입력값을 적용하게 됩니다.
하지만 Part Length의 경우 철근의 중심 선의 교점에서부터 Part Length를 적용하게 됩니다.
따라서 두 기능은 Hook Bending Radius만큼의 격차가 벌어지게 됩니다The direction of the rebar property determines the direction of creation of the hook.
This is a defining function.
Direction consists of two options
● Plane: A hook is created on the plane where the reinforcing bar is drawn.
● Custom: A hook is created with the rotation angle specified by the user in a non-planar direction .
When selecting the function of Custom, change the Rotate Angle value.
A window for input is activated.
Based on the reinforcing bar that the hook is dependent on
It rotates by the input value.
Figure 1. Comparison of Hook creation direction between Rotate Angle and Hook Angle
▶ Location
Location of Rebar Property is
Determines where the Offset is applied.
In other words, it is a function about where the Hook is created.
- Normal: Hook is created based on the inside of the transverse reinforcing bar line.
- Extended : Hook is created based on the outside of the transverse reinforcing bar line.
Figure 2. Comparison according to location setting
Angle / Radius / Length
▶ Hook Type : Hook 유형을 선택합니다Select the hook type.
Hook Type에서는 Hook를 설정하지 않거나 각도에 따른
Hook 유형을 선택할 수 있습니다.
또한 Custom을 선택하여 Hook Property를
사용자가 직접 입력할 수 있으며
In Hook Type, you do not set the hook or
You can choose the Hook type.
Also, select Custom to select Hook Property.
User can directly input
The Angle / Radius / Length 입력창이 활성화 됩니다input window is activated.
▶ Angle : Hook의 갈고리 각도를 입력합니다Input the hook angle of the hook.
▶ Radius : Hook의 곡률 반경을 입력합니다Enter the radius of curvature of the hook.
▶ Length : Hook의 길이를 입력합니다Enter the length of the hook.
그림 Figure 4. Hook Angle / Radius / Length
Align Option
Align Option
The Align Option, which determines the alignment method from the plane, consists of a total of 2 types.
● On/From Plane Cover Align Center
● Plane Alignment
그림 Figure 7. On/From Plane Cover Align Center
그림 Figure 8. Plane Alignment