[General Information]

• Template Name : Enter the name of the Assembly Unit to be created.

• Run Modify Mode after Creation : : If turned on, the Assembly Unit Mode automatically runs when the user creates the template after entering all the settings so that the created template model can be modified.

[Bridge Information]

• Number of Spans : Sets the number of spans. The template supports up to five consecutive spans.

[Guide]
Shows the variable information that defines the span configuration.

[Configuration]

• Support Name : Sets the library to be placed at the end of each span.

• Span Length : The final length for each span is automatically calculated and output based on the entered variable.

• Girder Length : Enter the Girder Length.

• Expansion Length : Enter the Expansion Length.

• Slab Protrusion Length : Enter the Slab Protrusion Length of the girder.

• Girder Connection : Enter the number of supports for the Girder Connection. 2Shoe is currently supported.

• Bearing Location B1 : Enter the distance between the continuous span girder end point to the support center.

• Bearing Location B2 : Enter the distance between the continuous span girder start point to the support center.

• Height Spacing : Enter the girder height.

Consider Bearing Bridge Widening : When set to On, the bridge widening input window for the beginning of the AUB model is activated.

Girder Alignment : Enter the offset between the alignment center and the structure center.

Girder Number : Sets the number of girders for the traverse cross section of the bridge. The provided template supports up to 10EA.

Layout Offset : Enter the offset between the alignment center and the structure center.

Girder Spacing : Enter the girder spacing.

Girder-1 : Enter the offset between the leftmost girder and the structure center across the bridge.

Girder-2, …, n : Enter the girder interval.

Consider Bearing Bridge Widening : When set to On, the bridge widening input window for the beginning of the AUB model is activated.

Pave. Thickness : Enter the thickness of the road pavement.

Slab Thickness : Enter the slab thickness.

Vertical Sag : Enter the additional separation distance for the vertical girder position.

Deck Width : Enter the width of the girder.

Spacing(L1) : Enter the width of the left railing of the bridge traverse cross section.

Spacing(L2) : The width of the left side road of the bridge traverse cross section is automatically input. (Entire Road Width - (Median Strip + Left Barrier + Right Barrier)) / 2

Spacing(L3) : Enter the median strip width.

Spacing(L4) : The width of the right side road to the cross section of the bridge is automatically input. (Entire Road Width - (Median Strip + Left Barrier + Right Barrier)) / 2

Spacing(L5) : Enter the width of the right railing of the bridge traverse cross section.

Type(L1 ~ 5) : Set the type of structure that will be placed at Spacing (L1 to 5).

Consider Bearing Bridge Widening : When set to On, the bridge widening input window for the beginning of the AUB model is activated.

[Cross Beam Location]

• Mid. Cross Beam : : Set the number of cross beams. The template supports up to three cross beams.

• Spacing(BS) : : Enter the position of the starting crossbeam in the longitudinal direction of the girder.

• Spacing(CR1) : Enter the location of the middle cross beam from the initial location of cross beam.

• Spacing(CR2) : Enter the position of the middle cross beam from the final location of cross beam.

• Spacing(BE) : Enter the final location of cross beam in the direction of the girder length.

[Girder Dimension & Cross Beam Detail]

• Girder

  • a : Enter the center width of the Girder.

  • b : Enter the width of the Girder.

  • c : Enter the height of the Girder.

• End Cross Beam

  • a : : Enter the height of the End Cross Beam.

  • b : Enter the thickness of the End Cross Beam.

• Middle Cross Beam

  • a : Enter the height of the Middle Cross Beam.

  • b : Enter the thickness of the Middle Cross Beam.

Consider Bearing Bridge Widening : When set to On, the bridge widening input window for the beginning of the AUB model is activated.

Bearing Height : Enter the bearing height. Click Apply to apply the height to all bearings.

Girder-1(Start) ~ 7(End) : The height can also be entered individually for each bearing.