개요
Spiral Rebar에 종속되는 Longitudinal Rebar Group의 분류, 형상, 배치, 수량 설정 등의 속성 정보를 확인, 또는 편집합니다.
실행
화면에서 Spiral Longitudinal Rebar Group을 선택.
설명
Common Tab
[Classification]
철근 그룹의 분류 속성을 설정합니다.Name : 철근 그룹의 이름을 입력합니다.
Rebar Type : 철근 유형을 출력합니다.
Grade : 철근 그룹의 재질을 설정합니다.
[Specification]
철근 그룹의 제원을 설정합니다.Code : Rebar Specification을 설정합니다.
Diameter : 철근의 직경을 선택합니다. Code가 선택된 경우에만 활성화됩니다.
Nominal Diameter : 철근의 공칭 직경을 입력합니다.
Bending Radius : 철근의 곡률 반경을 입력합니다.
Maximum Length : 철근 그룹 내 가장 긴 길이를 갖는 철근의 길이를 출력합니다.
Minimum Length : 철근 그룹 내 가장 짧은 길이를 갖는 철근의 길이를 출력합니다.
title | 상세 설명 (Diameter) |
---|
Diameter : ‘Code’가 선택된 경우에만 활성화됩니다.
Nominal Diameter : ‘Diameter’ 설정된 경우, 공칭 직경을 출력합니다. ‘Code : None’일 경우에만 직접 입력할 수 있습니다.
Summary
View or edit property information for classification, geometry, analysis, quantity settings of the Longitudinal Rebar Group that is dependent on the Spiral Rebar.
How to Run
Select the Spiral Longitudinal Rebar Group on the screen.
Explanation
Common Tab
[Classification]
Set the classification properties of the rebar group.Name : Enter the name of the rebar group.
Rebar Type : Displays the rebar type.
Grade : Sets the material grade of the rebar group.
[Specification]
Sets the specification of the rebar group.Code : Sets the rebar specification.
Diameter : Select the rebar diameter. This is enabled only when a code is selected.
Nominal Diameter : Enter the nominal diameter of the rebar.
Bending Radius : Enter the bending radius of the rebar.
Maximum Length : Displays the length of the longest rebar within the rebar group.
Minimum Length : Displays the length of the shortest rebar within the rebar group.
Expand | ||
---|---|---|
| ||
|
Info |
---|
[Hook]
Hook 형상을 설정합니다Set the shape of a hook.Differenct Start/End Hook : 시∙종점의 Hook 설정을 각각 적용할지 여부를 설정합니다Set whether to apply hook settings differently to the start and end point of the hook.
Hook Type : Hook 유형을 선택합니다Select the type of hook.
Angle : Hook의 갈고리 각도를 입력합니다Enter the angle of the hook.
Radius : hook의 곡률 반경을 입력합니다Enter the radius of the hook.
Length : Hook의 길이를 입력합니다Enter the length of the hook.
Expand | ||
---|---|---|
| ||
|
[Offset]
Rebar 양 끝단에서의 연장 길이를 조정합니다Adjust the extension length at both ends of the rebar.Start/End Length : 철근의 시∙종점의 연장 길이를 입력합니다. (+) 값일 경우 짧아지며 (-) 값일 경우 길어집니다Enter the extension length at the start and end of the rebar. Enter a positive (+) value to shorten, and a negative (-) value to extend.
Array Tab
[Arrangement]
철근의 간격을 설정합니다Sets the spacing for the rebars.Number of Rebars : Spiral Rebar에 배열되는 종철근의 개수를 입력합니다. 해당 개수에 맞춰 등간격으로 배열됩니다Enter the number of longitudinal rebars that are arranged in the spiral rebar. The rebars are spaced equally based on the number of rebars entered.
Expand | ||
---|---|---|
| ||
|
[Splice]
철근 그룹의 이음을 설정합니다Set the splice for the rebar group.
Expand | ||
---|---|---|
| ||
|
[Variable Rebar Name]
철근 그룹 내 이름 규칙을 설정합니다Sets the name rule within the rebar group.Array Group : 배열된 철근 각각의 이름을 다르게 지정합니다Set the name of each arranged rebar differently.
Splice Group : 겹이음 단위로 철근 그룹을 구분하여 이름을 다르게 지정합니다Set the name of each regar group according to the splice group.
Construction Tab
Info |
---|
Reference - Construction 속성Properties |