Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Table of Contents
기능 개요

Overview of Functions

Info

Stiffener를 Draw하는 기능입니다Draw a stiffener.

기능 설명

Details of Functions

Draw Tab > Transverse Stiffener

Draw transverse stiffener

Info

횡방향 텐던을 모델링하는 기능입니다.

총 2가지 방식으로 모델링 할 수 있습니다The ability to model transverse tendons.

There are two ways to model.

  • Select Edge(s) : 화면상의 Edge를 선택해서 Stiffener를 생성하는 기능입니다Creates a stiffener by selecting an edge on the screen.
    - Reverse direction : 옵션 체크 시, Edge를 기준으로 반대방향에 Stiffener가 생성됩니다If checked, the stiffener is created in the reverse direction based on the edge.

  • Sketch On Edge : Edge를 따라 직접 2점을 입력해 Stiffener를 생성하는 기능입니다Creates a stiffener by entering two points directly along the edge.
    - Reverse direction : 옵션 체크 시, Edge를 기준으로 반대방향에 Stiffener가 생성됩니다If checked, the stiffener is created in the reverse direction based on the edge.

  • Reverse direction : 선택한 Edge의 반대방향으로 Stiffener가 생성됩니다Stiffeners are created in the opposite direction of the selected edge.

Alignment of points

Displayed when Sketch On Edge 선택 시 표출is selected

Info

Stiffener가 Array 될 때, Pick point 지점이 edge 방향을 따라가는 옵션을 결정합니다When the stiffeners are arrayed, the pick point determines the options along the edge direction.

  • By ratio : In Tapered array , Pick pick point 1 , 2 지점이 edge의 ratio 지점을 찾아 array되도록 합니다and 2 are arranged to find the ratio point of the edge. (Default)

  • By distance : In Tapered array , Pick point 1 , 2 지점이 각각 edge 위의 가까운 가장자리로부터 일정한 distance 지점을 찾아 array되도록 합니다and 2 are arranged to find a certain distance point from the near edge on the edge.

Draw Tab > Longitudinal Stiffener

Draw longitudinal stiffener

Info

종방향 텐던을 모델링하는 기능입니다.

총 3가지 방식으로 모델링 할 수 있습니다The ability to model longitudinal tendons.

There are three ways to model.

  • Single : 평면 상에 존재하는 타겟 부재의 edge 내의 1개의 점을 클릭해 longitudinal stiffener를 생성합니다Click on a point on the edge of the target member that exists on the plane to create a longitudinal stiffener.

  • Select Edge : 평면 상에 존재하는 타겟 부재의 edge를 선택해 longitudinal stiffener를 생성합니다Select the edge of the target member that exists on the plane to create a longitudinal stiffener.

  • 2 Points : 평면 상에 존재하는 타겟 부재의 edge 내의 2개의 점을 클릭해 longitudinal stiffener를 생성합니다.

  • Reverse : stiffener가 반대방향으로 생성됩니다.

  • Horizontal : Stiffener 생성 시 X축과 평행하게 생성합니다Click two points within the edge of the target member that exist on the plane to create a longitudinal stiffener.

  • Reverse : The stiffener is created in the opposite direction.

  • Horizontal : Create stiffeners parallel to the X axis.

  • Reverse start point : 속성값이 적용되는 시/종점을 변경하는 옵션입니다. (Select Edge일 시시 표출This option changes the time / end point to which the property value is applied. (Expressed in Select Edge)

Property Tab > 1st sub tab

Classification

Info

종방향/횡방향 Stiffener의 분류 속성을 정의합니다Define the classification properties for the longitudinal and lateral stiffeners.

  • Auto name : On일 때, 자동으로 Stiffener의 속성을 정의합니다If it is checked on, the Stiffener automatically defines its properties.
    Transverse Stiffener
    - Prefix : T / Start number : 1 / Class : 1
    Longitudinal Stiffener
    - Prefix : L / Start number : 1 / Class : 1

  • Name : Stiffener의 이름을 결정합니다Input the name of a stiffener.

Property Tab > 2nd sub tab

Section

Info

Stiffener의 Section 유형을 선택합니다Select the type of stiffener.

  • Flat : Thickness, Height

  • Angle : Height, Breadth, Web thickness, Flange thickness

  • T-section : Height, Breadth, Web thickness, Flange thickness

  • I-section : Height, Breadth1 ∙ 2, Web thickness, Flange thickness1 ∙ 2, Rounding radius 1 ∙ 2

  • U-section : Height, Breadth1, Breadth2, Thickness, Rounding radius

End shape

Info

Stiffener 시/종점부의 형상에 관한 설정입니다.

Flat Section 일 때 표출

This setting is for the shape of the stiffener at the start/end point.

Displayed when the flat section is selected.

  • Cutting type : 시/종점부에 각각 Chamfer / Fillet을 적용할 수 있습니다Chamfer / Fillet can be applied to the start/end point.

Displayed when the Flat / Angle / T Section 일 때 표출section are selected.

  • Hole type : 시/종점부에 각각 Chamfer / Scallop을 적용할 수 있습니다.

Image Removed

Flat Section 일 때 표출

  • Offset : 시/종점부에 각각 Offset을 적용할 수 있습니다Chamfer / Scallop can be applied to the start/end point.

Image Added

Displayed when the flat section is selected.

  • Offset : Offset can be applied to the start and end points respectively.
    - Start length : Stiffener를 그릴 때 시점으로부터 start length 입력 값만큼 offset되어 그려집니다When drawing a stiffener, it is drawn offset from the start length by the input value.
    - End length : Stiffener를 그릴 때 시점으로부터 end length 입력 값만큼 offset되어 그려집니다When you draw a stiffener, it is drawn offset from the point by the end length input.

- From start plane : Stiffener를 생성하는 Plane으로부터 입력 값만큼 offset되어 생성됩니다The offset is generated by the input value from the plane generating the stiffener.
- From end plane : Array에서 정의의하는 Plane으로부터 입력 값만큼 offset되어 생성됩니다It is created offset by input value from Plane defined in Array.

Property Tab > 3rd sub tab

Array spacing

Info

Longitudinal stiffener의 간격을 설정합니다Sets the spacing for longitudinal stiffeners.

Spacing 옵션으로 options include Adjustable spacing, By number, Limit Max. spacingSpacing, Pattern spacing , User defined를 제공합니다and User defined are provided.

  • Spacing type : Select the Spacing type을 설정합니다type.
    Adjustable Spacing : 사용자가 목표로 한 간격 값만큼 배열 후, 남은 나머지 간격으로 stiffener를 배근합니다.  옵션에 따라서 시점, 종점, 중간점의 stiffener 간격을 조정합니다After arranging by the interval value you aim, the stiffener is moved to the remaining intervals. Optionally adjust the stiffener spacing between the start, end, and midpoint.
    - Adjust at
      ① First spacing : After arranging the Base Spacing 값으로 배열 후, 남은 나머지 값을 첫 번째 stiffener 간격에서 조정합니다. values, adjust the remaining values in the first stiffener interval.
      ② Last spacing : Base Spacing 값으로 배열 후, 남은 나머지 값을 마지막 stiffener 간격에서 조정합니다.  After arranging the Base Spacing values, adjust the remaining values from the last stiffener interval.
      ③ First/Last spacing : Base Spacing 값으로 배열 후, 남은 나머지 값을 첫 번째와 마지막 stiffener 간격에 나누어 조정합니다.  After arranging by Base Spacing value, adjust the remaining value by dividing the remaining value by the first and last stiffener spacing.
      ④ Middle spacing : Base Spacing 값으로 배열 후, 남은 나머지 값을 중간 stiffener 간격(홀수일경우 시점에 가까운쪽)에서 조정합니다.  After arranging the Base Spacing values, adjust the remaining values at the middle stiffener spacing (closer to the point if odd).
    - Base spacing : 목표로 한 간격값을 설정합니다. Array 경로를 따라 해당 값만큼 나누어 배치합니다Set the target interval value. Arrange the values by their values along the Array path.  

  • by Number : 간격과 관계없이 입력한 개수만큼을 등간격으로 배열합니다. Arranges the number entered equally, regardless of the spacing.
    - Number of rebar : 배열하고자 하는 stiffener의 개수를 입력합니다. Enter the number of stiffeners you want to arrange.

  • Limit Max.spacing : 입력된 값을 넘지 않는 간격으로 배열합니다. Arrange at intervals not exceeding the value entered.
    - Max. spacing : 간격의 최대값을 입력합니다. 입력된 간격보다 큰 간격을 허용하지 않고 stiffener를 배열합니다. 

  • Pattern spacing : 입력한 값만큼만 배열하고 추가로 배열하지 않습니다. 
    - Spacing : 이곳에 입력된 간격값으로 배열하고 해당 간격보다 작은 간격은 배열하지 않습니다. 

  • User defined : 사용자가 원하는 간격으로 입력합니다. 
    - Spacing : 사용자가 원하는 간격을 직접 입력합니다. Enter the maximum value for the interval. Arrange the stiffeners without allowing a gap greater than the entered interval.

  • Pattern spacing : Arranges only as much as you enter, but no additional arrays.
    - Spacing : The interval value entered here is arranged and the interval smaller than the interval is not arranged.

  • User defined : Type in the interval you want.
    - Spacing : Enter the user-defined interval. (ex. 3@200, 400, 5@150)